Jump to content

17 Lost fish (was Help, fish dieing)


blueether

Recommended Posts

I have just done what was going to be about a ~60% water change, but ended up being ~75% as I over fulled the tank.

I disturbed some of the rocks/wood/substrate.

When I turned off the water (hose end in the tank) I had just come from doing the dishes, quickly dried my hands on way to tank and turned off the hose end with maybe still damp hands from the dishwater.

No test kits here so cant test water.

About 350-400 lt of water in a 4ft tank.

Have removed all the smelt and at least 6 have died so far with the other dozen or so not responding well, some in the small bully tank and some in the outside trough.

All the bullies and inanga look fine so far so here's hoping they pull through ok.

Edit:

14 smelt dead so far :tears:

Link to comment
Share on other sites

Chlorine in water?

I doubt that residual soap on your hands would be enough to kill the fish but depends on what you use to wash the dishes. Always wash my hands with hand soap and rinse them before putting hands in my tanks.

What were the fish the fish doing before they died? Flashing, Gulping air?

Link to comment
Share on other sites

Could have been chlorine in the water, I ask my old man what the water values are for today (works in the dairy factory) as he/they test the water.

The fish started by looking stressed (light coloured) then swimming erratically then fast jerky swimming and then just stopping and floating upside down. All of this would happen within 5-10 min (most in less than 5 min) of the first stress signs.

Even the ones removed before showing any stress died fast once they started to show colour loss.

Some of them you could see the blood vessels in the head/gill covers

Link to comment
Share on other sites

Some of them you could see the blood vessels in the head/gill covers

Reddening around the gills is usually a sign of chemical burns of the gills. My guess would be Chlorine.

Does your local supply get treated with chlorine normally?

Wanganui water supply gets regularly dosed with chlorine but especially after large rainfall the council ups the chlorine levels. Our water supply is bore water.

Link to comment
Share on other sites

Our water is normally dosed with chlorine, and we have had alot of rain so the powers that be might have upped the dose, but I couldn't smell any extra in the water.

I guess if it was enough to kill fish then my tank will be restarting it's cycle, well at least there is only 1/2 the bio-load in there now :facepalm:

Link to comment
Share on other sites

All up I have lost 17 fish, that is all my smelt, from doing a too large a water change (by the looks).

That just leaves about 8 bullies; Cran's, common and maybe a giant bully, 2 koura and maybe 12 inanga in over 350 lt of crisp cold water.

I guess I'll be going on a fish hunt this week/weekend, maybe I replace the smelt with some kokopu?

Link to comment
Share on other sites

Very sorry for your losses :(

Was it only smelt or other species too?

Had the tank been well-maintained before this? Perhaps you stirred up too much gunk from the bottom? I have often done 50-75% waterchanges on natives and had no problem (Palmy water is also chlorinated) but killed everything with a major waterchange and gravelvac after having let maintenance slip for a while.

You may be tempted to use dechlorinators in the future, but these would be toxic to your crays. Can't win. :facepalm:

(I just did a 50% change on my tank with some new smelt, will be keeping a close eye now!)

Link to comment
Share on other sites

Was it only smelt or other species too?
Only the smelt, one of the biggest inanga did look a little stressed bu was fine by today

Had the tank been well-maintained before this? Perhaps you stirred up too much gunk from the bottom?
There had been the auto water changer running up until 2 weeks when I disconnected as it needed the window open for the hoses, during the clean I scrubbed 2 of the sides of algae and moved 2 bits of large drift wood and a large stone to make room for another bit of wood (maybe the new wood?), no real substrate movement...

I did a bigger w/c as I wasn't watching the tank, normally only run it 3/4 full it is now to within 15mm of the top

Link to comment
Share on other sites

  • 5 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...