Teshe

@maxxi1 just wanting to confirm, is it this one here? https://www.kings.co.nz/daltons-aquatic-mix-15l-984245

Hey, looking to start my own black worm culture to add them into my tanks feed rotation but having trouble finding a starter colony. Any advice or anyone willing to sell me some would be appreciated

Hey guys, I was looking to see if anyone has any experience using cheaper alternatives to the aquatic soils available from pet shops. I have run across this article that uses organic potting mixes, but I was looking at pond soils. They are safe for fish, have all the basic needs of a substrate, and the main issue people at the store said I would run into is cloudy water as the dirt becomes mud and gets kicked up by the digging fish. I was wondering if I could fill filter socks or pond pump covers with the soil, and put it in the higher parts of the tank with a sand cap, so the plants can get in, but it is contained in case of any curious fish. Advice and anecdotes are welcome, I just cant justify to fill a 200L with fluorite or aquasoil if there is a cheaper (even if slower) alternative.

Given the responses I have done some work on the filter housing with a 3D mock-up. Walls will be glass attached with Silicone, lid and outflow cap will be 3D printed plastic and wont be submerged. There is a small water hold in the bottom of the lid to allow the bonsai some drainage. Going to use a Juniper as it is evergreen, hardy, and shouldn't need a lot of soil which lowers my risks of anything leeching in to the water. Should also easily lift out but remain securely in place due to support on all 4 sides. Any thoughts? Obvious oversights? Or things you think I should consider, add, or remove?

Hey guys, I am starting work on a new paludarium for some Japanese fire-bellies and I wanted some opinions/advice. I am working on an ambitious plan for it. To start, I have this 70L tank, it has a hood with build in slots for the UV lights, and should make escape proofing the tank both easier and hidden. So now for the complex part. The rough requirements for the newts as I understand them are 30% land, 60% water. So my plan is to make an interior enclosure or reservoir using glass walls and silicone. Inside this I plan to house the water filter, heater (If I need one, I am south Auckland so I am not entirely sure it is necessary), and a water pump that will feed into a small trickle over some rocks from their little island. Here is a mock-up, the interior dimensions are wrong but bear with me! The complex part is I want to create a planter that slots over this, that will house some small plants, mosses, and a hardy little bonsai. The bonsai will shade the water with its branches and provide both lit and shaded areas for the newts on land. I can 3D print the pot/lid for it, but I am wondering if I will need to add more supports along the two tank wall sides. I was thinking I could add a horizontal shelf along the back that will hold the pump outlet, and can be dressed with some rocks to hide it. Will this be likely to be strong enough if it is just silicone holding on to the sides? Or will I be better off adding in some glass struts in the reservoir? Also, if I add struts, would I be better off having them along the edge to give the most open area in the filter box, or will that affect flow, and the better option be to put a couple of supports central to the tank to hold the lid up? The end goal is to have a stepped staircase of stones leading to a deeper pond along the front of the tank. I am also hoping this will promote a lazy circulation, as I know the newts do not like a strong current. I am also planning to plant the bottom of the aquatic areas to increase the water cleanliness, as ideally I want to work towards a low maintenance setup once it is established. Who knows, if it works might even be able to get a couple minnows (Done some research and found some that are rumoured to be good tank mates) but that is more a stretch goal and not part of the current planning. I want to clarify I do not currently have any animals waiting to move in so I can really take my time and getting this build right, so any advice or ideas towards my goal would be awesome. Thank you!