livingart Posted March 11, 2010 Report Share Posted March 11, 2010 i tell you what, give me the size of the tank & the overall size of teh cab & i will draw one up tomorrow morning & do a cutting list. Quote Link to comment Share on other sites More sharing options...
smidey Posted March 11, 2010 Report Share Posted March 11, 2010 Brief: Tank size is 600mm long x 300mm wide, height is 300mm but irrelevant. Must be made from a single 2400x600mm 18mm sheet of MDF using only MDF. Cutting instructions must be simple and use as few cuts as possible. Aesthetics are also very important. :lol: man, you don't ask for much. i particularly like this part :lol: Cutting instructions must be simple and use as few cuts as possible. Aesthetics are also very important. :lol: i shall make it work Quote Link to comment Share on other sites More sharing options...
SamH Posted March 11, 2010 Author Report Share Posted March 11, 2010 man, you don't ask for much. i particularly like this part :lol: Ditto. I can't work without a clear design brief i shall make it work I can't wait to see it! I tried again but mm's at this time of night does not compute. Quote Link to comment Share on other sites More sharing options...
smidey Posted March 11, 2010 Report Share Posted March 11, 2010 i have done the plan & cutting pattern but cannot get it into a jpg format, tiff & pdf only so i will email it to you. 8) Quote Link to comment Share on other sites More sharing options...
SamH Posted March 20, 2010 Author Report Share Posted March 20, 2010 Got it all cut now, the guy who cut it forgot to take off the 50mm for waste and I only realised when I got home :oops: Cut it with a hand saw but now I can hardly type and it's all wonky. Otherwise he cut all the pieces exactly to size right down to the mm with almost no waste from blade width. Quote Link to comment Share on other sites More sharing options...
Sophia Posted March 21, 2010 Report Share Posted March 21, 2010 bit late for me to join in but my tank has the same dimensions as yours and this is what my husband made out of some heavy as particle board we found at the emporium. we had 3 pieces of it and there is a hole in the back for the wiring to be contained inside the cupboard the lid is not attached Quote Link to comment Share on other sites More sharing options...
SamH Posted March 21, 2010 Author Report Share Posted March 21, 2010 Thanks Sophia Stand is all together now, only problem is the doors. There is a 10mm gap between them in the centre, one is too tight and the other won't shut properly. Otherwise, an easy to make and sturdy stand. Quote Link to comment Share on other sites More sharing options...
Carlos & Siran Posted March 21, 2010 Report Share Posted March 21, 2010 Sounds good, are you using adjustable hinges?, here's a helpful tip, every measurement is made up in multiples of 32mm. So the hinge holes should be 32mm from the front of the cabinet, and the holes should be 32mm apart, this includes pretty much everything to do with kitchen/cabinet making hardware. As for adjusting the hinges, it's quite a tricky exercise, you just have to keep persevering. If you can't get it, Me, or Smidey no doubt, will try and run you through it. Quote Link to comment Share on other sites More sharing options...
SamH Posted March 21, 2010 Author Report Share Posted March 21, 2010 Thanks Carlas & Siran. Just using plain old hinges, nothing fancy. As long as the doors poen and close then I'm happy Just had two coats of paint and a bit of wood to stop the loose door from opening without the sticky door opening first. Keeps the cupboard shut 8) Quote Link to comment Share on other sites More sharing options...
Sophia Posted March 21, 2010 Report Share Posted March 21, 2010 mine stay closed by way of a magnet type catch on the inside Quote Link to comment Share on other sites More sharing options...
smidey Posted March 21, 2010 Report Share Posted March 21, 2010 it is best to get cabinet door hinges as they are adjustable & you make the overall appearance look alot better by aligning them up. if you take your doors to a kitchen maker it will take less than 10 mins to bore them & fit hinges, i use to do it occasionally when i was at the kitchen place. just ask them to be bored 100mm down. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.